Products accepted at or below 10°C, route targets around 48 jam, payload that fits the 250 X 140 X 320 mm usable space, and lanes where a 32°C test profile is close to the expected shipping environment.
10°C and Below Chilled Packout
Packout Kotak EPS untuk Pengiriman 48 Jam di Bawah 10°C
For chilled products that must stay at or below 10°C, Tempk can supply a passive EPS packout using 14 pieces of 380g 0°C biological ice packs. In the tested 11L payload layout, the shortest measured point stayed below 10°C for 51.2 hours in a 32°C constant-temperature environment.
≤10°C
Target upper temperature limit for this tested chilled packout.
51.2H
Shortest measured duration below 10°C among seven sensor positions.
32°C
Constant ambient environment used for the original Tempk test.
11L
Effective payload space after 14 ice packs are placed in the EPS box.
Gunakan kasing
Gunakan packout ini jika produk hanya membutuhkan batas atas di bawah 10 °C
This packout is intended for buyers who need a practical starting point for quotation, sample testing or route validation. The key question is whether your product size, route time and temperature rule are close to the tested 11L EPS configuration.
Produk yang sensitif terhadap pembekuan, variable warehouse dwell time, summer routes above the tested profile, or products that require a different sensor layout or test standard.
Strict 2-8°C pharmaceutical lanes, Pengiriman beku, dry ice lanes, ultra-cold requirements, or products that must stay above a lower temperature limit without additional validation.
Packout Parameters
Konfigurasi teruji: kotak EPS 21 L dengan ruang muatan efektif 11 L
These values describe the tested Tempk configuration for this packout. Match them against product size, massa produk, route duration and ambient exposure before placing a bulk order.
Kotak EPS dan media pendingin
| Parameter | Tested Value | Buyer Note |
|---|---|---|
| EPS external dimensions | 400 X 290 X 470 mm | Use for carton, pallet and storage planning. |
| EPS internal dimensions | 300 X 190 X 370 mm | Gross internal space before coolant placement. |
| EPS wall thickness | 50 mm | Insulation structure used in the tested setup. |
| Nominal EPS volume | 21 L | Box volume is not the same as usable payload space. |
| Effective payload space | 250 X 140 X 320 mm, kira-kira. 11 L | Product must fit after ice packs are arranged. |
| Media pendingin | 14 pieces of 380g 0°C biological ice packs | Placed around the payload as shown in the packout image. |
| Ice pack dimensions | 182 X 97 X 25 mm | Useful for checking contact area and product clearance. |
| EPS box weight | 0.66 kg | Box only, before coolant and product. |
| Total cooling media weight | 5.32 kg | 14 X 0.38 kg. |
| EPS box plus ice packs | 5.98 kg | Product weight and outer carton are additional. |
If the payload dimensions, product mass or allowed temperature window changes, use this tested layout as a starting point and validate the modified configuration before bulk procurement.
Test Result
51,2 jam di bawah 10 °C pada uji suhu lingkungan 32 °C
The shortest measured point was the top center position. For buyer planning, 51.2 hours is the conservative number from the original Tempk test, giving a 3.2-hour margin over a 48-hour requirement.
51.2H
Shortest duration below 10°C, measured at the top center point.
56.5H
Longest measured position in this test, recorded at the bottom corner.
48jam+
The tested configuration met the more-than-48-hour requirement.
7 pts
Internal measurement positions used to compare warm spots in the box.
| Sensor Location | Duration Below 10°C | How to Read It |
|---|---|---|
| Bottom of the box | 54.2 jam | Lower-position reading in the EPS cavity. |
| Bottom corner | 56.5 jam | Longest measured position in this set. |
| Front center | 53.5 jam | Mid-facing point near the product space. |
| Middle center | 52.9 jam | Core payload-area measurement point. |
| Right center | 52.4 jam | Side measurement point near coolant placement. |
| Top center | 51.2 jam | Shortest measured position and the practical planning number. |
| Top corner | 51.8 jam | Upper corner measurement point near the lid area. |
Panduan Seleksi
Bagaimana pembeli dapat memutuskan apakah mulai dari packout ini
This configuration is most useful when the temperature requirement, route time and payload size are close to the tested case. For different risk profiles, Tempk can adjust coolant quantity, box type or validation method.
Start here if the product can accept near-0°C exposure and only needs to remain below 10°C during the route.
Because the coolant phase-change point is 0°C, products with lower-limit concerns should be tested with the real payload and packing method.
Consider larger box volume, lebih banyak pendingin, different insulation, lane-specific preconditioning or a new temperature profile test.
Those requirements need a dedicated packout and acceptance rule instead of borrowing this below-10°C test result.
Test Context
Apa yang dibantu dikonfirmasi oleh foto uji
The photo gives buyers a practical view of how the packout was prepared. Untuk pengadaan, the important question is whether your product, payload mass and handling route match the original test closely enough.
Apa yang perlu diperiksa Tempk sebelum konfirmasi sampel
Confirm product dimensions, payload weight and whether the product can fit inside the 250 X 140 X 320 mm effective space.
Confirm whether the product only needs an upper limit below 10°C or also has a lower temperature limit.
Compare route duration, paparan lingkungan, warehouse dwell time and handoff points with the 32°C test condition.
Prepare a route-specific or customer-specific validation if the order requires a temperature report before bulk purchase.
RFQ Checklist
Detail yang mempercepat penawaran dan rencana sampel
Send these inputs with the inquiry so Tempk can compare this tested packout with modified EPS, EPP, PU or VIP options when needed.
Persyaratan produk
Allowed temperature range, lower-limit sensitivity, ukuran produk, payload weight and whether direct contact with coolant is allowed.
Profil rute
Waktu transit, expected ambient temperature, pickup and delivery country, warehouse dwell time and final delivery condition.
Packout target
Durasi sasaran, box size preference, disposable or reusable preference, carton requirements and labeling needs.
Testing need
Sensor positions, Kriteria penerimaan, report format and whether the buyer needs a sample test before bulk order.
Commercial plan
Sample quantity, volume bulanan, tujuan, target price level and whether OEM or custom packaging is required.
Proses penanganan
Preconditioning time, freezer or cold-room availability, packing labor conditions and handoff time before carrier pickup.
Buyer Questions
Pertanyaan umum untuk proyek kotak EPS di bawah 10 °C
Berapa lama packout ini bertahan di bawah 10 °C?
The shortest measured position stayed below 10°C for 51.2 hours in a 32°C constant-temperature environment.
Konfigurasi apa yang diuji?
The tested setup used a 21L EPS insulated box, 11L effective payload space and 14 pieces of 380g 0°C biological ice packs.
Apakah ini otomatis memenuhi rute saya?
TIDAK. It is a tested result from one configuration. Your route should be checked against payload size, sensitivitas produk, transit time and ambient exposure.
Apakah ini bisa digunakan untuk produk farmasi 2-8 °C?
Use a dedicated 2-8°C pharmaceutical packout instead. This solution supports a below-10°C upper-limit requirement, not a narrow regulated range.
Mengapa ruang muatan usable hanya 11 L?
The EPS box is listed as 21L, but the tested payload space is about 11L because the 14 ice packs occupy space around the payload.
Bisakah Tempk menyesuaikannya untuk rute yang lebih panjang?
Ya. Tempk can compare insulation material, ukuran kotak, ice pack quantity and sensor layout, then prepare a modified sample test.
Butuh packout kotak di bawah 10 °C untuk rute 48 jam?
Share your payload size, persyaratan suhu, route duration and purchase plan. Tempk can check whether this 11L EPS packout is suitable or prepare an adjusted sample packout before bulk procurement.
Hubungi Tempk